Amana Ice Maker D7824703 User Manual

IC8 Top and Bottom Freezer Refrigerator Ice Maker Kit  
Installation and Operating Instructions  
Parts  
Introduction  
Use listed part numbers only when ordering replacement  
parts. Part number are not used in installation instructions.  
!
Recognize this symbol as a  
safety precaution.  
7
6
Read entire manual before installing kit. All necessary tools  
and materials must be available prior to installation. Verify  
all listed parts are included in kit. If parts are missing,  
contact source from whom kit was purchased.  
5
• Mechanical experience is required to install kit.  
• If unable to solve a problem during installation, contact  
an authorized Amana technician. Locate a Factory  
Service Center or independent authorized technician by  
calling 1-800-628-5782 inside U.S.A. and 1-319-622-  
5511 outside U.S.A. Service is at owner’s expense.  
8
10  
9
4
13  
3
Safety Instructions  
1
2
11  
12  
!
WARNING  
To avoid electrical shock which can cause severe  
personal injury or death, unplug power cord or open  
household circuit breaker to refrigerator before installing  
kit. After installing kit, reconnect power.  
!
Caution  
Item Description  
Part number  
D7824703  
10519801  
To avoid property damage, observe the following:  
• Confirm water pressure to water valve is at least 20  
pounds per square inch.  
• Start nuts by hand to avoid cross threading. Finish  
tightening nuts using a wrench. Do not overtighten.  
• Check carefully for water leaks prior to returning  
refrigerator to normal location and 24 hours after  
connection.  
1
2
3
Ice maker  
Ice maker cover  
5/8" long sheet metal screw (to  
secure ice maker)  
M0211118  
4
5
6
7
Stainless steel clip  
Ice maker wire harness clamp  
Ice maker wire harness  
Ice maker arm  
B5720302  
10526701  
D7813004  
10884401  
M0311301  
A3124301  
10319801  
8
Button plug  
9
Oblong plug  
Before Connecting Ice Maker  
10  
Thermal fuse clip (attached to  
ice maker)  
Important  
• Before connecting ice maker, contact a plumber to  
connect copper tubing for refrigerator water supply to  
household plumbing in compliance with local codes and  
ordinances.  
Use1/4" (6 mm) flexible copper tubing. Length of copper  
tubing must reach from water supply connection plus an  
additional 8' (2.5 m) for service loop behind refrigerator.  
Tubing should be soft instead of rigid and ends should be  
free of burrs.  
11  
12  
13  
N/S  
Plastic clips (4)  
Ice storage bucket  
M0104106  
10476201  
10244904  
A3036901  
Compression nut and sleeve  
Warning level (attached to side  
of ice maker)  
Diagnostic label (inside ice  
maker cover)  
N/S  
N/S  
10834701  
10527033  
Installation Instructions  
N/S= Not shown  
Copper tubing route must be above 35°F (2°C) to prevent  
water line from freezing.  
 
Insert screws  
5/8" sheet metal  
screws here  
Clips  
Important  
Ice maker can be installed one way only. Do not drill  
additional holes.  
Install Ice Maker  
7. Hold ice maker in position. Verify two outside electrical  
flats line up with flats in receptacle on freezer back wall.  
Insert wire harness plug into receptacle on rear wall  
until locking fingers on plug snap into place. Slip ice  
maker hanger over sheet metal screw.  
1. Remove any shelves that may obstruct installation of  
ice maker module.  
Models with ice service rack  
Slide ice service rack toward front of freezer until  
screws are in middle of mounting holes. Gently pull ice  
service rack away from freezer. Remove screws using  
a 1/4" hex nut driver. Insert provided plugs into screw  
holes.  
Wire harness  
Wire harness  
receptacle  
plug  
Bottom Freezer models  
Remove freezer shelf and basket.  
Top Freezer models  
Sheet metal  
screw  
Ice maker  
hanger  
Remove freezer shelf.  
2. Install hole plugs to properly position for ice maker.  
Models with half-width freezer shelves  
Push 2 oblong plugs provided, into 2 lowest shelf slots  
on left side.  
or  
Models with full freezer shelves  
Push 1 oblong plug provided, into lowest shelf slot on  
each side.  
Wire harness  
Wire harness  
receptacle  
plug  
Sheet metal  
screw  
Ice maker  
hanger  
3. Remove ice maker from shipping carton and discard  
packing material.  
Important  
Ice maker is shipped with arm down. This is correct  
position for ice production. Do not force arm up or  
down.  
4. Slip stainless steel clip over rear wall of ice maker water  
cup.  
8. Ease ice maker water cup toward end of water fill tube.  
Water fill tube fits under stainless steel clip. Water fill  
tube must not be kinked. Water fill tube elbow should  
extend 3/8" into ice maker water cup and must be  
secured under stainless steel clip.  
Stainless  
steel clip  
Water  
cup  
Stainless  
Water fill tube  
steel clip  
Water  
cup  
5. Remove and discard 3 button plugs from left freezer  
wall using flat blade screwdriver with blade covered with  
masking tape.  
6. Start 5/8" sheet metal screw in top front hole, and top  
rear hole in left wall. Leave heads out approximately  
3/8".  
9. Install remaining 5/8" long sheet metal screw to secure  
ice maker. Tighten all 3 screws.  
10. Reinstall freezer shelf and and any baskets.  
11. Position ice storage bucket on freezer shelf under ice  
maker.  
 
• Stop ice production by lifting ice maker arm. A definite  
click is heard when off position is reached. Ice maker  
arm will remain in off position until ice maker arm is  
pushed down.  
!
Caution  
To avoid property damage, all covers must be in place.  
12. Plug in refrigerator and move refrigerator in place. Level  
if necessary.  
13. Check for water leaks 24 hours after installation.  
!
Caution  
To avoid damage to ice maker, observe the following:  
• Do not force ice maker arm down or up.  
• Do not place or store anything on icemaker or in ice  
storage bucket.  
Operating Instructions  
• Confirm ice bucket is in place and ice maker arm is  
down.  
Before Calling For Service  
Off position  
Allow ice maker 1 overnight period to make ice before  
assuming a difficulty exists.  
Ice maker arm  
If ice maker is not producing ice  
• Confirm ice maker arm is down.  
• Confirm household water supply is reaching water valve.  
• Confirm ice maker wiring harness is completely inserted  
into electrical receptacle.  
• Check electrical connections to water valve coil.  
• Check for kinks in copper or plastic tubing. Remove  
kinks or replace tubing.  
On position  
• After freezer section reaches normal temperature, ice  
maker fills with water and begins operating. Allow 24–48  
hours after installation before first harvest of ice. Ice  
maker produces 7 to 9 harvests of ice in a 24-hour period  
under ideal conditions.  
• Confirm freezer is operating at proper temperature.  
• After ice is formed, ice maker drops ice cubes into  
ice storage bucket. During ice production, ice maker arm  
raises and lowers. When ice storage bucket is full, ice  
maker arm turns ice maker off. Discard first 3 harvests of  
ice after initially connecting refrigerator to household  
water supply and after extended periods of non-use.  
If ice maker is not producing enough ice  
• Ice maker produces 7 to 9 harvests of ice in a 24-hour  
period under ideal conditions.  
• See above section.  
If ice maker makes unfamiliar sounds  
• These may be normal. Refer to Normal Operating  
Sounds section in Owner's Manual.  
Warranty  
Ice Maker Full One Year Warranty  
First Year  
Amana Appliances will repair or replace, free of charge, any part which is defective due to workmanship or materials.  
Owner's Responsibilities  
Warranty Limitations  
• Provide proof of purchase (sales receipt).  
• Provide normal care and maintenance. Replace owner  
replaceable items where directions appear in Owner's  
Manual and Installation Instructions.  
• Begins at date of original purchase.  
• Applies to product used within the United States or in  
Canada if product has Canadian Standards Association  
listing when shipped from the factory.  
• Make product reasonably accessible for service.  
• Pay for premium service costs for service outside  
technician's normal business hours.  
• Service must be performed by an authorized Amana  
technician.  
Warranty Is Void If  
• Pay for service calls related to product installation or  
customer education.  
• Product is used on a commercial, rental or leased basis.  
• Product has defect or damage due to an accident, fire,  
flood, connection to an improper electrical or water supply,  
lightning, product alteration, shipping and handling, or other  
conditions beyond the control of Amana .  
• Product is improperly installed or used.  
In no event shall Amana Appliances be liable for incidental  
or consequential damages*  
*This warranty gives you specific legal rights and you may have  
others which vary from state to state. For example, some  
states do not allow the exclusion or limitation of incidental or  
consequential damages so this exclusion may not apply to you.  
Part No. 10527033  
Printed in U.S.A.  
1998 Amana Appliances  
Amana, Iowa 52204  
 

Absocold Corp Refrigerator ARD492 User Manual
Acer Computer Monitor AL2032 User Manual
Acer Laptop VDT39V1001 User Manual
Acroprint Time Clock ATR20 20 User Manual
ADS Technologies Digital Camera PYRO 1394 User Manual
Agilent Technologies Cable Box 8590 User Manual
Aiwa Stereo System CX NA31 User Manual
Altinex Stereo Receiver DS801 111 User Manual
Axis Communications Camera Lens DSL203 User Manual
Beko Refrigerator CN232121 User Manual